Choosing a through-the-wall AC for a new installation

More checks neededGE

AJCQ08AXXWA

Nominal supply: 115 V
Nominal cooling rating: 7,800 BTU/h
Heating: Cooling only
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 10.6

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJCQ08AXXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJCQ08AXXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
GE projected Quick Specs — AJCQ08AXXWA, AJCQ12AXXWA ↗Single-page exact-model sheet: drawing, CEER and plug/circuit rows; explicitly marked Projected specifications — subject to change. Not final electrical evidence. · Checked 2026-10-12

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AJCQ12AXXWA

Nominal supply: 115 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 10.5

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJCQ12AXXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJCQ12AXXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
GE projected Quick Specs — AJCQ08AXXWA, AJCQ12AXXWA ↗Single-page exact-model sheet: drawing, CEER and plug/circuit rows; explicitly marked Projected specifications — subject to change. Not final electrical evidence. · Checked 2026-10-12
GE AJCQ12AXXWA — conflicting FEATURES EER ↗Specs & Details > FEATURES > EER: 10.6. CAPACITY > Cooling EER in the same page reports 10.5. These are two section citations, not independent documents. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AJCQ12DXXWA

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 10.5

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJCQ12DXXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJCQ12DXXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
GE projected Quick Specs — AJCQ12DXXWA ↗Single-page exact-model sheet: drawing, CEER and plug/circuit rows; explicitly marked Projected specifications — subject to change. Not final electrical evidence. · Checked 2026-10-12

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AJEQ12DCXWA

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Electric heat
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 9.5

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJEQ12DCXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJEQ12DCXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
GE projected Quick Specs — AJEQ12DCXWA ↗Single-page exact-model sheet: drawing, CEER and plug/circuit rows; explicitly marked Projected specifications — subject to change. Not final electrical evidence. · Checked 2026-10-12

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AJVQ12ACXWA

Nominal supply: 115 V
Nominal cooling rating: 12,000 BTU/h
Heating: Heat pump with electric backup
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 9.6

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJVQ12ACXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJVQ12ACXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AJVQ12DCXWA

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Heat pump with electric backup
Plug: Not established
Specified circuit / fuse: Not established
CEER (nominal rating): 9.5

Inverter documentedWi-Fi documented

Installation: GE RAB26A · required kit included; GE RAB46B · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB26A, GE RAB46B. Installation conditions apply.

Verify circuit rating, plug, outlet

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Exact plug configuration is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.
Required receptacle is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB26A

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB26A with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

GE RAB46B

Manufacturer sleeve association; listed conditions apply.

Supplied security bracket and screws · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB46B with the RAG13A rear grille. Use the full sleeve/chassis instructions.
Confirm specified rear grille and airflow. A retained louvered grille must follow the 45-degree instruction; do not substitute a grille by dimensions.
Install the supplied security bracket with its flange behind the sleeve edge, as specified on printed page 16.
Confirm exact unit nameplate, grounded outlet and circuit; remaining unknown electrical fields must be resolved before recommendation.
For a new installation the sleeve is purchased separately from the chassis.
For heat-capable models, apply all page-16 combustible-material clearances: sides 1 in, front and exterior rear 20 in, above 39-3/8 in, below as the manual’s 4-7/8–6-3/8 in range. Resolve the applicable bottom clearance for the actual installation; do not select an endpoint as a general rule.

Evidence for this model and installation

GE 26-inch inverter owner and installation manual ↗Cover lists all six exact AJ models and INVERTER. Printed/PDF pages 15–16: RAB26A/RAB46B with RAG13A, depth without front, supplied security bracket, grille and heat-model clearance requirements. No numeric branch-circuit requirement in the final English manual. · Checked 2026-10-13
GE AJVQ12DCXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AJVQ12DCXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001195

Manufacturer specifications ↗

More checks neededGE

AKCQ08AXXXA

Nominal supply: 115 V
Nominal cooling rating: 7,800 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: Not established
CEER (nominal rating): 9.6

Inverter documented

Installation: GE RAB24 · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB24. Installation conditions apply.

Verify circuit rating

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB24

Manufacturer sleeve association; listed conditions apply.

Supplied grille, seals, trim, grounding wire and 24-inch security brackets; use applicable parts · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB24 with the supplied stamped aluminum outdoor grille.
Use the 24-inch sleeve brackets and the applicable sealing, grounding, grille and trim procedures on printed pages 15–24.
Confirm exact nameplate, grounded outlet and circuit; the sleeve association does not prove electrical suitability.
RAB24 sleeve is purchased separately; supplied trim/installation hardware is not a wall sleeve.
Use the applicable sleeve procedure: secure sound housing, required rearward slope, supplied grounding wire with toothed washers, seals and trim; do not leave required hardware unused.
Use the supplied 24-inch brackets for RAB24 or 26-inch brackets for RAB26A, with flanges behind the sleeve edge; attach both sides as specified on page 24.

Evidence for this model and installation

GE 24-inch inverter owner and installation manual ↗Cover lists all four exact AK models and INVERTER. Printed/PDF pages 15–19 and 23–24: bare chassis, RAB24/RAB26A, supplied hardware, rearward slope, grounding, GE rear grille, trim and correct 24/26-inch security brackets. RAB26A recommendation spells RAG13 (not RAG13A). No numeric branch-circuit requirement. · Checked 2026-10-13
GE AKCQ08AXXXA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AKCQ08AXXXA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13
GE AKCQ08AXXXA — conflicting FEATURES EER ↗Specs & Details > FEATURES > EER: 9.6. CAPACITY > Cooling EER in the same page reports 10.6. These are two section citations, not independent documents. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001293

Manufacturer specifications ↗

More checks neededGE

AKCQ12AXXXA

Nominal supply: 115 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: Not established
CEER (nominal rating): 9.5

Inverter documented

Installation: GE RAB24 · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB24. Installation conditions apply.

Verify circuit rating

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB24

Manufacturer sleeve association; listed conditions apply.

Supplied grille, seals, trim, grounding wire and 24-inch security brackets; use applicable parts · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB24 with the supplied stamped aluminum outdoor grille.
Use the 24-inch sleeve brackets and the applicable sealing, grounding, grille and trim procedures on printed pages 15–24.
Confirm exact nameplate, grounded outlet and circuit; the sleeve association does not prove electrical suitability.
RAB24 sleeve is purchased separately; supplied trim/installation hardware is not a wall sleeve.
Use the applicable sleeve procedure: secure sound housing, required rearward slope, supplied grounding wire with toothed washers, seals and trim; do not leave required hardware unused.
Use the supplied 24-inch brackets for RAB24 or 26-inch brackets for RAB26A, with flanges behind the sleeve edge; attach both sides as specified on page 24.

Evidence for this model and installation

GE 24-inch inverter owner and installation manual ↗Cover lists all four exact AK models and INVERTER. Printed/PDF pages 15–19 and 23–24: bare chassis, RAB24/RAB26A, supplied hardware, rearward slope, grounding, GE rear grille, trim and correct 24/26-inch security brackets. RAB26A recommendation spells RAG13 (not RAG13A). No numeric branch-circuit requirement. · Checked 2026-10-13
GE AKCQ12AXXXA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AKCQ12AXXXA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13
GE AKCQ12AXXXA — conflicting FEATURES EER ↗Specs & Details > FEATURES > EER: 9.5. CAPACITY > Cooling EER in the same page reports 10.5. These are two section citations, not independent documents. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001293

Manufacturer specifications ↗

More checks neededGE

AKCQ12DXXXA

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: NEMA 6-15P
Specified circuit / fuse: Not established
CEER (nominal rating): 9.5

Inverter documented

Installation: GE RAB24 · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB24. Installation conditions apply.

Verify circuit rating

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB24

Manufacturer sleeve association; listed conditions apply.

Supplied grille, seals, trim, grounding wire and 24-inch security brackets; use applicable parts · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB24 with the supplied stamped aluminum outdoor grille.
Use the 24-inch sleeve brackets and the applicable sealing, grounding, grille and trim procedures on printed pages 15–24.
Confirm exact nameplate, grounded outlet and circuit; the sleeve association does not prove electrical suitability.
RAB24 sleeve is purchased separately; supplied trim/installation hardware is not a wall sleeve.
Use the applicable sleeve procedure: secure sound housing, required rearward slope, supplied grounding wire with toothed washers, seals and trim; do not leave required hardware unused.
Use the supplied 24-inch brackets for RAB24 or 26-inch brackets for RAB26A, with flanges behind the sleeve edge; attach both sides as specified on page 24.

Evidence for this model and installation

GE 24-inch inverter owner and installation manual ↗Cover lists all four exact AK models and INVERTER. Printed/PDF pages 15–19 and 23–24: bare chassis, RAB24/RAB26A, supplied hardware, rearward slope, grounding, GE rear grille, trim and correct 24/26-inch security brackets. RAB26A recommendation spells RAG13 (not RAG13A). No numeric branch-circuit requirement. · Checked 2026-10-13
GE AKCQ12DXXXA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AKCQ12DXXXA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13
GE AKCQ12DXXXA — conflicting FEATURES EER ↗Specs & Details > FEATURES > EER: 9.5. CAPACITY > Cooling EER in the same page reports 10.5. These are two section citations, not independent documents. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001293

Manufacturer specifications ↗

More checks neededGE

AKVQ12DXXWA

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Heat pump with electric backup
Plug: NEMA 6-20P
Specified circuit / fuse: Not established
CEER (nominal rating): 9.5

Inverter documentedWi-Fi documented

Installation: GE RAB24 · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: GE RAB24. Installation conditions apply.

Verify circuit rating

Why these facts need checking

Required circuit / fuse rating is not established in the reviewed documentation. Check the exact unit nameplate or ask GE to confirm it before purchase.

Checks before purchase (5)

Confirm the actual supply voltage.
The manufacturer circuit/fuse rating is not established. Check the exact unit nameplate or ask GE to confirm it before purchase; your circuit answer cannot fill this gap.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

GE RAB24

Manufacturer sleeve association; listed conditions apply.

Supplied grille, seals, trim, grounding wire and 24-inch security brackets; use applicable parts · Required for the listed procedure · Included as reported in source

The exact-model manual recommends RAB24 with the supplied stamped aluminum outdoor grille.
Use the 24-inch sleeve brackets and the applicable sealing, grounding, grille and trim procedures on printed pages 15–24.
Confirm exact nameplate, grounded outlet and circuit; the sleeve association does not prove electrical suitability.
RAB24 sleeve is purchased separately; supplied trim/installation hardware is not a wall sleeve.
Use the applicable sleeve procedure: secure sound housing, required rearward slope, supplied grounding wire with toothed washers, seals and trim; do not leave required hardware unused.
Use the supplied 24-inch brackets for RAB24 or 26-inch brackets for RAB26A, with flanges behind the sleeve edge; attach both sides as specified on page 24.

Evidence for this model and installation

GE 24-inch inverter owner and installation manual ↗Cover lists all four exact AK models and INVERTER. Printed/PDF pages 15–19 and 23–24: bare chassis, RAB24/RAB26A, supplied hardware, rearward slope, grounding, GE rear grille, trim and correct 24/26-inch security brackets. RAB26A recommendation spells RAG13 (not RAG13A). No numeric branch-circuit requirement. · Checked 2026-10-13
GE AKVQ12DXXWA — manufacturing dates ↗Owner Center > Manufactured start/end dates; a fixed past end date indicates discontinued production, not lack of retailer stock. · Checked 2026-10-13
GE AKVQ12DXXWA — exact product specifications ↗Specs & Details: POWER / RATINGS, FEATURES, ACCESSORIES, WEIGHTS & DIMENSIONS; only product specification fields retained. Hidden obsolete/out-of-stock template strings are not lifecycle/stock evidence. · Checked 2026-10-13
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13

2025/2026 inverter generation; exact full SKU covered by 49-5001293

Manufacturer specifications ↗

More checks neededLG

LT1016CER

Nominal supply: 115 V
Nominal cooling rating: 9,800 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10.6

Installation: LG AXSVA1 · required kit included; LG AXSVA4 · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

Reported indoor noise: 56 dBA (Manufacturer rating; fan speed and test conditions not stated). Test conditions vary by source.

What matches (1)

Documented sleeve option: LG AXSVA1, LG AXSVA4. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

LG AXSVA1

Manufacturer sleeve association; listed conditions apply.

Supplied installation parts: grille, applicable insulation, shims and trim; sleeve sold separately · Required for the listed procedure · Included as reported in source

The current exact-UPC manufacturer sheet lists this sleeve as a separately sold optional accessory. Check the exact housing and model nameplate.
Follow LGE sleeve Procedure A, including serviceable rear flange/grille, specified rearward slope, applicable supplied seals/shims and trim; sleeve is secured to the wall.
115 V model: use the documented 15 A circuit and matching grounded 5-15 plug/receptacle. Do not assume the existing outlet or circuit from the old unit.

LG AXSVA4

Manufacturer sleeve association; listed conditions apply.

Supplied installation parts: grille, applicable insulation, shims and trim; sleeve sold separately · Required for the listed procedure · Included as reported in source

The current exact-UPC manufacturer sheet lists this sleeve as a separately sold optional accessory. Check the exact housing and model nameplate.
Follow LGE sleeve Procedure A, including serviceable rear flange/grille, specified rearward slope, applicable supplied seals/shims and trim; sleeve is secured to the wall.
115 V model: use the documented 15 A circuit and matching grounded 5-15 plug/receptacle. Do not assume the existing outlet or circuit from the old unit.

Evidence for this model and installation

LG US wall air conditioner category ↗Eleven LT equipment entries observed in initial category HTML; accessories excluded. Dynamic pagination is not proof of complete coverage. · Checked 2026-10-12
LG owner manual — cool ↗Support associations checked 2026-10-12; visually reviewed 2026-10-13. Printed/PDF page 9 explicitly lists LT0816CER, LT1016CER, LT12124CNR (115 V) and LT1036CER, LT1236CER, LT1430CNR (230 V), 15 A circuit and outlet drawings; pages 11–13 packing list and LGE sleeve Procedure A. LT1216CER has a separate exact support manual. · Checked 2026-10-13
LG LT1016CER — current product specifications ↗Specifications > Electrical Ratings, Performance, Features and Dimensions/Weight; public page specification data; product modelStatus ACTIVE checked separately from stock. · Checked 2026-10-13
LG LT1016CER — exact support/document association ↗Selected support sales suffix and Download Manuals list; suffix is not automatically an alias of another physical generation. · Checked 2026-10-12
LG LT1016CER — linked specification sheet ↗Exact SKU specifications, refrigerant and Optional Accessories. Dates differ across PDFs; older electrical/performance tables are not merged into current page values. · Checked 2026-10-12
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13

Reviewed marketed SKU and UPC 048231379618; selected support LT1016CER.AT1AUSL. Base model is not an alias of every historical sales suffix.

Manufacturer specifications ↗

More checks neededFriedrich

UCT08B10A

Nominal supply: 115 V
Nominal cooling rating: 8,000 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10.1

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT08B10A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT08B10A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UCT10B10A

Nominal supply: 115 V
Nominal cooling rating: 10,000 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10.1

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT10B10A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT10B10A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UCT10B30A

Nominal supply: 230 V
Nominal cooling rating: 10,000 BTU/h
Heating: Cooling only
Plug: NEMA 6-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10.1

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT10B30A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT10B30A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UCT12B10A

Nominal supply: 115 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT12B10A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT12B10A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UCT12B30A

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Cooling only
Plug: NEMA 6-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 10

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT12B30A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT12B30A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UCT14B30A

Nominal supply: 230 V
Nominal cooling rating: 14,000 BTU/h
Heating: Cooling only
Plug: NEMA 6-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 9.3

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UCT14B30A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UCT14B30A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UET08B11A

Nominal supply: 115 V
Nominal cooling rating: 8,000 BTU/h
Heating: Electric heat
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 9.6

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET08B11A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UET08B11A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UET10B33A

Nominal supply: 230 V
Nominal cooling rating: 10,000 BTU/h
Heating: Electric heat
Plug: NEMA 6-20P
Specified circuit / fuse: 20 A
CEER (nominal rating): 9.6

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET10B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UET10B33A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UET12B33A

Nominal supply: 230 V
Nominal cooling rating: 12,000 BTU/h
Heating: Electric heat
Plug: NEMA 6-20P
Specified circuit / fuse: 20 A
CEER (nominal rating): 9.6

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET12B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UET12B33A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

UET14B33A

Nominal supply: 230 V
Nominal cooling rating: 14,000 BTU/h
Heating: Electric heat
Plug: NEMA 6-20P
Specified circuit / fuse: 20 A
CEER (nominal rating): 9.3

Wi-Fi documented

Installation: Friedrich USC · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (1)

Documented sleeve option: Friedrich USC. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET14B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich USC

Manufacturer sleeve association; listed conditions apply.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

Provided installation kit: specified grille, seals and centering/grounding materials · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Follow the recommended USC procedure on printed pages 14–15: use the specified dual-intake grille, seals, centering materials and grounding wire. Remove weather panels before operation. Maintain the prescribed 3/8-inch downward slope from front to back. Optional architectural louver UXAA is sold separately and is not the supplied kit SKU.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Friedrich USEZ

Sleeve decision needs review.

Sources disagree on a fit-critical fact. This option cannot be a confirmed fit.

Decorative trim ring supplied with chassis · Required for the listed procedure · Included as reported in source

The 2026 exact-series brochure requires USC/USEZ for new installations; sleeve is sold separately.
Use included trim ring and applicable sealing/grille components according to the exact R-32 manual. Remove weather panels before operation.
Match actual unit nameplate and grounded supply to the electrical table; capacity must also suit the room.

Evidence for this model and installation

Uni-Fit 2026 brochure — model specifications ↗Printed page 4 / PDF page 4: all ten UCT/UET B-series, final A-suffix R-32 models · Checked 2026-10-13
Uni-Fit 2026 brochure — electrical requirements ↗Printed page 5 / PDF page 5: exact model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-13
Uni-Fit 2026 brochure — existing sleeve table ↗Printed page 6 / PDF page 6: explicitly named Friedrich WSE column; chassis dimensions and included decorative trim ring · Checked 2026-10-13
Uni-Fit 2026 brochure — standard features ↗Printed page 3 / PDF page 3: built-in Wi-Fi and cooling/electric-heat series · Checked 2026-10-13
Uni-Fit R-32 installation manual — WSE and preparation ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; printed/PDF pages 14–16: WSE table, generic sleeve preparation, required rear grille, sealing and grounding · Checked 2026-10-13
Uni-Fit R-32 installation manual — receptacles ↗Cover / PDF page 1 exact voltage groups; printed page 17 / PDF page 17, Table E.1: receptacle and circuit ratings for corresponding UCT/UET voltage groups · Checked 2026-10-13
Uni-Fit 2026 — native sleeve and new installation ↗Printed page 6: USC/USEZ required for new installation, sold separately; sleeve and finished-opening dimensions; included trim ring. · Checked 2026-10-13
USEZ sleeve assembly and installation instructions ↗Pages 1, 3 and 5: exact USEZ identity, housing dimensions and supplied rear grille; differs from 2026 combined USC/USEZ dimensions. · Checked 2026-10-13
Uni-Fit R-32 manual — supplied installation parts ↗Cover / PDF page 1 exact models; printed/PDF page 8 packing list; pages 14–16 provided dual-intake grille and installation methods · Checked 2026-10-13
AJ Madison — exact UET14B33A destination ↗Product heading and model identity only. Retailer specifications are not used as installation evidence; price and stock are not imported. · Checked 2026-10-13

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗

More checks neededFriedrich

WCVT12B10B

Nominal supply: 115 V
Nominal cooling rating: 13,500 BTU/h
Heating: Cooling only
Plug: NEMA 5-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 13.2

Inverter documentedWi-Fi documented

Installation: Friedrich WSE · follow listed conditions

What matches (1)

Documented sleeve option: Friedrich WSE. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

Friedrich WSE

Manufacturer sleeve association; listed conditions apply.

External condensate drain kit (DK) · Optional or conditional · Package inclusion not established

Confirm an actual WSE sleeve in serviceable condition. The exact B-suffix model appears in the brochure's installation table, whose note requires a WSE sleeve; dimensions alone are not the evidence for this relation.
Verify the rear grille against the manufacturer installation requirements. Incorrect airflow can recirculate discharge air and cause shutdown; do not assume an old grille is suitable.
Check the actual installation for this 115 V model, NEMA 5-15P plug and manufacturer-specified 15 A circuit/fuse. Cooling running current is a separate specification.
DK is an optional external drain kit when connection to a condensate disposal system is necessary or desired. It is not a general requirement for every WSE replacement.

Evidence for this model and installation

WallMaster 2026 brochure — exact model specifications ↗Printed page 5 / PDF page 5: inverter model specifications and model sizing list · Checked 2026-10-12
WallMaster 2026 brochure — chassis and WSE sleeve ↗Printed page 6 / PDF page 6: chassis, sleeve and finished-hole tables; WSE requirement · Checked 2026-10-13
WallMaster 2026 brochure — electrical requirements ↗Printed page 6 / PDF page 6: exact B-suffix model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-12
WallMaster 2026 brochure — grilles and drain kits ↗Printed page 7 / PDF page 7: WSE, WSEZ, rear grille orientation, DK/IDK and BAK conditions · Checked 2026-10-13
WallMaster 2026 brochure — standard features ↗Printed page 8 / PDF page 8: compressor type and built-in Wi-Fi; broad performance ranges are not used as model specifications · Checked 2026-10-12
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13

2026 WallMaster inverter / R-32, final B suffix (BR_WM_REV 07-15-25)

Manufacturer specifications ↗

More checks neededFriedrich

WCVT16B30B

Nominal supply: 230 V
Nominal cooling rating: 16,800 BTU/h
Heating: Cooling only
Plug: NEMA 6-15P
Specified circuit / fuse: 15 A
CEER (nominal rating): 12.6

Inverter documentedWi-Fi documented

Installation: Friedrich WSE · follow listed conditions

What matches (1)

Documented sleeve option: Friedrich WSE. Installation conditions apply.

Checks before purchase (5)

Confirm the actual supply voltage.
Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
Exact plug/receptacle configuration needs confirmation.
Room estimate or model capacity at the selected voltage needs checking.
Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Sleeves, required parts and sources

Friedrich WSE

Manufacturer sleeve association; listed conditions apply.

External condensate drain kit (DK) · Optional or conditional · Package inclusion not established

Confirm an actual WSE sleeve in serviceable condition. The exact B-suffix model appears in the brochure's installation table, whose note requires a WSE sleeve; dimensions alone are not the evidence for this relation.
Verify the rear grille against the manufacturer installation requirements. Incorrect airflow can recirculate discharge air and cause shutdown; do not assume an old grille is suitable.
Check the actual installation for this 230 V model, NEMA 6-15P plug and manufacturer-specified 15 A circuit/fuse. Cooling running current is a separate specification.
DK is an optional external drain kit when connection to a condensate disposal system is necessary or desired. It is not a general requirement for every WSE replacement.

Evidence for this model and installation

WallMaster 2026 brochure — exact model specifications ↗Printed page 5 / PDF page 5: inverter model specifications and model sizing list · Checked 2026-10-12
WallMaster 2026 brochure — chassis and WSE sleeve ↗Printed page 6 / PDF page 6: chassis, sleeve and finished-hole tables; WSE requirement · Checked 2026-10-13
WallMaster 2026 brochure — electrical requirements ↗Printed page 6 / PDF page 6: exact B-suffix model groups, circuit/fuse ratings and NEMA plugs · Checked 2026-10-12
WallMaster 2026 brochure — grilles and drain kits ↗Printed page 7 / PDF page 7: WSE, WSEZ, rear grille orientation, DK/IDK and BAK conditions · Checked 2026-10-13
WallMaster 2026 brochure — standard features ↗Printed page 8 / PDF page 8: compressor type and built-in Wi-Fi; broad performance ranges are not used as model specifications · Checked 2026-10-12
NEMA receptacle configurations — manufacturer reference ↗Printed/PDF page 12: labelled 5-15R, 6-15R and 6-20R face drawings. Used only to identify the matching receptacle drawn in an exact AC manual, never to infer the required breaker. · Checked 2026-10-13

2026 WallMaster inverter / R-32, final B suffix (BR_WM_REV 07-15-25)

Manufacturer specifications ↗

Choosing a through-the-wall AC for a new installation

Choose the sleeve before the opening

Check what the package actually contains

Choose capacity and power together

Can I install a window AC in the wall?

What should I give an installer?

23 profiles with the requirement documented

Documented for this scenario (23)

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB26A

GE RAB46B

Evidence for this model and installation

GE RAB24

Evidence for this model and installation

GE RAB24

Evidence for this model and installation

GE RAB24

Evidence for this model and installation

GE RAB24

Evidence for this model and installation

LG AXSVA1

LG AXSVA4

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich USC

Friedrich USEZ

Evidence for this model and installation

Friedrich WSE

Evidence for this model and installation

Friedrich WSE

Evidence for this model and installation

LG AXSVA1

LG AXSVA4

Evidence for this model and installation

LG AXSVA1

LG AXSVA4

Evidence for this model and installation

LG AXSVA1

LG AXSVA4

Evidence for this model and installation