Wall AC FitStart selection
FIND YOUR WALL AC
Buying guide ↗Start over

230-volt through-the-wall air conditioners with electric heat for Friedrich WSE

Selected: Keep an existing sleeve · Friedrich WSE · 230 V supply · Electric resistance heat

Compare 230 V with electric heat candidates for the Friedrich WSE sleeve. Refine by room area, outlet, circuit, inverter and Wi-Fi.

3 models still in consideration0 meet documented filters · 3 need checksSee models ↓

3 models still in consideration

The shortlist updates with each answer. Confirm room capacity, electrical supply and installation conditions before purchase. Seller stock and prices have not been checked.

Refine your shortlist

Circuit breaker / fuse
Sun, occupants and other sizing adjustments

Cooling estimate: needs a sizing check · ENERGY STAR chart ↗

Voltage, outlet configuration and circuit protection are separate checks. Missing or disputed feature data stays unconfirmed; indoor noise data is not a “quietest” ranking.

Catalog coverage (33 profiles)

More checks needed (3)

Unknown or disputed facts remain visible in each profile. These are candidates for verification, not installation approvals.

More checks neededFriedrich

UET10B33A

Nominal supply
230 V
Cooling at 230 V
10,000 BTU/h
Heating
Electric heat
Plug
NEMA 6-20P
Specified circuit / fuse
20 A
CEER at 230 V
9.6
Wi-Fi documented

Installation: Friedrich WSE · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (3)
  • Documented sleeve option: Friedrich WSE. Installation conditions apply.
  • 230 V operation is documented.
  • Documented heating type meets your choice; heating output and operating limits still need assessment.
Checks before purchase (4)
  • Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
  • Exact plug/receptacle configuration needs confirmation.
  • Room estimate or model capacity at the selected voltage needs checking.
  • Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET10B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich WSE

Manufacturer sleeve association; listed conditions apply.

Provided Uni-Fit installation kit: specified dual-intake grille, seals and centering/grounding materials; confirm package contents · Required for the listed procedure · Included as reported in source

Included decorative trim ring · Required for the listed procedure · Included as reported in source

  • The current brochure and the exact-generation R-32 manual name Friedrich WSE among existing sleeves. Verify that the actual housing is securely installed and structurally sound; do not infer identity from a 27-inch measurement alone.
  • Use generic-sleeve Method B on printed page 16, with the specified dual-intake grille, sealing and centering materials and grounding wire. Remove the old rear grille. Optional Method A and architectural louver UXAA on page 15 are specified for USC, not this WSE procedure.
  • The manual describes a provided installation kit. Confirm that the exact unit package includes the required grille and seals; obtain manufacturer confirmation of replacement part numbers if these pieces are missing. No separate kit SKU is established in this record.
  • Use the included decorative trim ring to cover the gap around the smaller chassis. Follow the prescribed sealing and 3/8-inch downward slope from front to back; use the manual’s shimming procedure if needed.
  • Check the installation for the exact 230 V model, NEMA 6-20P plug, NEMA 6-20R receptacle and manufacturer-specified 20 A circuit/fuse. Do not derive the circuit from cooling running current.

Evidence for this model and installation

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗
More checks neededFriedrich

UET12B33A

Nominal supply
230 V
Cooling at 230 V
12,000 BTU/h
Heating
Electric heat
Plug
NEMA 6-20P
Specified circuit / fuse
20 A
CEER at 230 V
9.6
Wi-Fi documented

Installation: Friedrich WSE · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (3)
  • Documented sleeve option: Friedrich WSE. Installation conditions apply.
  • 230 V operation is documented.
  • Documented heating type meets your choice; heating output and operating limits still need assessment.
Checks before purchase (4)
  • Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
  • Exact plug/receptacle configuration needs confirmation.
  • Room estimate or model capacity at the selected voltage needs checking.
  • Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET12B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich WSE

Manufacturer sleeve association; listed conditions apply.

Provided Uni-Fit installation kit: specified dual-intake grille, seals and centering/grounding materials; confirm package contents · Required for the listed procedure · Included as reported in source

Included decorative trim ring · Required for the listed procedure · Included as reported in source

  • The current brochure and the exact-generation R-32 manual name Friedrich WSE among existing sleeves. Verify that the actual housing is securely installed and structurally sound; do not infer identity from a 27-inch measurement alone.
  • Use generic-sleeve Method B on printed page 16, with the specified dual-intake grille, sealing and centering materials and grounding wire. Remove the old rear grille. Optional Method A and architectural louver UXAA on page 15 are specified for USC, not this WSE procedure.
  • The manual describes a provided installation kit. Confirm that the exact unit package includes the required grille and seals; obtain manufacturer confirmation of replacement part numbers if these pieces are missing. No separate kit SKU is established in this record.
  • Use the included decorative trim ring to cover the gap around the smaller chassis. Follow the prescribed sealing and 3/8-inch downward slope from front to back; use the manual’s shimming procedure if needed.
  • Check the installation for the exact 230 V model, NEMA 6-20P plug, NEMA 6-20R receptacle and manufacturer-specified 20 A circuit/fuse. Do not derive the circuit from cooling running current.

Evidence for this model and installation

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗
More checks neededFriedrich

UET14B33A

Nominal supply
230 V
Cooling at 230 V
14,000 BTU/h
Heating
Electric heat
Plug
NEMA 6-20P
Specified circuit / fuse
20 A
CEER at 230 V
9.3
Wi-Fi documented

Installation: Friedrich WSE · required kit included

Kit inclusion refers to the listed installation parts. Confirm sleeve supply separately.

What matches (3)
  • Documented sleeve option: Friedrich WSE. Installation conditions apply.
  • 230 V operation is documented.
  • Documented heating type meets your choice; heating output and operating limits still need assessment.
Checks before purchase (4)
  • Compare the actual circuit with the exact manufacturer circuit/fuse requirement.
  • Exact plug/receptacle configuration needs confirmation.
  • Room estimate or model capacity at the selected voltage needs checking.
  • Enter 100–2,500 sq ft for the ENERGY STAR chart. Other room sizes need an individual sizing assessment.

Check the exact model at a store

UET14B33A at AJ Madison ↗Model identity checked 2026-10-13

Ordinary store links; no affiliate commission. Confirm the model, nameplate, sleeve, parts, price and availability with the seller before ordering.

Sleeves, required parts and sources

Friedrich WSE

Manufacturer sleeve association; listed conditions apply.

Provided Uni-Fit installation kit: specified dual-intake grille, seals and centering/grounding materials; confirm package contents · Required for the listed procedure · Included as reported in source

Included decorative trim ring · Required for the listed procedure · Included as reported in source

  • The current brochure and the exact-generation R-32 manual name Friedrich WSE among existing sleeves. Verify that the actual housing is securely installed and structurally sound; do not infer identity from a 27-inch measurement alone.
  • Use generic-sleeve Method B on printed page 16, with the specified dual-intake grille, sealing and centering materials and grounding wire. Remove the old rear grille. Optional Method A and architectural louver UXAA on page 15 are specified for USC, not this WSE procedure.
  • The manual describes a provided installation kit. Confirm that the exact unit package includes the required grille and seals; obtain manufacturer confirmation of replacement part numbers if these pieces are missing. No separate kit SKU is established in this record.
  • Use the included decorative trim ring to cover the gap around the smaller chassis. Follow the prescribed sealing and 3/8-inch downward slope from front to back; use the manual’s shimming procedure if needed.
  • Check the installation for the exact 230 V model, NEMA 6-20P plug, NEMA 6-20R receptacle and manufacturer-specified 20 A circuit/fuse. Do not derive the circuit from cooling running current.

Evidence for this model and installation

UCT/UET B-series, final A suffix, R-32; specifications scoped to the 2026 brochure revision 02-19-25

Manufacturer specifications ↗
Outside the current filters (9) — see why
  • UCT08B10ADocumented nominal supply is 115 V; your answer is 230 V. Documented heating type does not meet your heating choice.
  • UCT10B10ADocumented nominal supply is 115 V; your answer is 230 V. Documented heating type does not meet your heating choice.
  • UCT10B30ADocumented heating type does not meet your heating choice.
  • UCT12B10ADocumented nominal supply is 115 V; your answer is 230 V. Documented heating type does not meet your heating choice.
  • UCT12B30ADocumented heating type does not meet your heating choice.
  • UCT14B30ADocumented heating type does not meet your heating choice.
  • UET08B11ADocumented nominal supply is 115 V; your answer is 230 V.
  • WCVT12B10BDocumented nominal supply is 115 V; your answer is 230 V. Documented heating type does not meet your heating choice.
  • WCVT16B30BDocumented heating type does not meet your heating choice.

Check electric heating separately

Electric resistance heat adds requirements beyond the cooling estimate. Check the exact model’s heating output, required supply, plug and circuit protection in its manufacturer documentation. The room-AC cooling chart is not a heating-load calculation.

Manufacturer documents for this shortlist: Uni-Fit 2026 brochure — model specifications ↗ · Uni-Fit 2026 brochure — electrical requirements ↗ · Uni-Fit 2026 brochure — existing sleeve table ↗

What the shortlist can establish

The engine separates documented requirements, missing or disputed facts and known exclusions. Models marked “More checks needed” are not purchase approvals. This is a limited catalog of Friedrich, LG and GE; it does not cover every available wall air conditioner.

Sources behind this catalog selection (11)

Room sizing, supply and installation guide →

Read the sleeve profile and fit conditions →